Sensors - Controllers
SCP Series Speed Switch Resettable Speed Switch System • Single or dual relay set points adjustable from 1-1,000 RPM. • Built-in start delay. • Dial-in calibration does not require power. • Fail-safe operation in over speed and under speed mode. • Split collar pulser wraps available when end of shaft is inaccessible. • Explosion proof/waterproof housing contains sensor and electronics. • Optional EZ-Mount bracket available. |
M Series Speed Switch Miniature Speed Switch System • Single set point adjustable from 10-100 RPM (M100), or 100-5,000 RPM (M5000). • Single-turn potentiometer for easy calibration. • Split collar pulser wraps available when end of shaft is inaccessible. • Compact explosion proof housing contains sensor and electronics. • Optional EZ-Mount bracket available. • Spanish language cut sheet available for this product |
||||
M100T/M5000T  Miniature Speed Switch System • Terminal block for easy wiring. • Cast aluminum housing is explosion proof and waterproof. • Optional voltages available. • Easy installation and calibration. • Compact, self-contained system with sensor and switch. • Rugged system is dust, dirt and greaseproof. • Optional EZ-Mount bracket available. • Spanish language cut sheet available for this product. |
 NEW
!!! - EVOLUTION CUBEDControllers with independent timer, up to 4 relay or VDC for SSR driving outputs, reduced depth, energy saving options, Wattmeter and hour counters - 1/16 DIN - 48 x 48 mm - 78 x 35 mm - 48 x 96 mm |
||||
K31 Mini-programmer controller - Panel mount controller 78 x 35 mm - 1 Configurable probe input - 2 digital inputs - Up to 5 digital outputs - PID controller with: * Independent timer * 8 segment programmer (optional) * Wattmeter * Counter for worked days and hours * Compressor protection timer - TTL or RS485 Modbus-RTU ports - 1 display line, 4 digit, h 12 mm, red colour |
ZTT-11/RD Head mount PT100 transmitter Input from RTD PT100, 2 wires output • Low Cost • Linearized input for PT100 sensors 2 or 3 wires • Scale range max: -200 ... 850 °C • Output 4 ... 20 mA 2 wires • Loop supply 10 ... 30 V • Programming button • LED operation indicator • Programmable with software and USB interface (optional) • Interface and instrument supplied by USB port • Head mounting • Dimensions (Ø x D): 43 x 21 mm |
||||
ZTT-51/GD DIN rail mount PT100 transmitter PT100 input, 2 wires output • SMART, programmable • Linearized input for PT100 sensors • Scale range max: -200 ... 850 °C • PT100 2 or 3 wires • Output 4 ... 20 mA 2 wires • Input and output isolated from each other • Loop supply 11 ... 30 VDC • Burnout, ranges and units of measure (°C -°F)programmable • Programmable with software and USB interface (optional) • Interface and instrument supplied by USB port • DIN rail mounting • Dimensions (W x H x D): 17.5 x 90 x 56.4 mm |
ZIS 3X Infrared sensor with air purge - Field mount contactless temperature sensor - Process connection: threaded M12 x 1.0 - Stainless Steel - Minimum diameter: 6mm - Measuring ratio: 3:1 (17°) - Linearised as thermocouple K signal |
||||
HS Humidity and temperature transmitter for snow making machines - Specifically designed for snow making cannons - Field mount relative humidity electronic transmitter - With replaceable "Humy-chip" capacitive sensor and filters |
KR1 Controller with independent timer |
||||
HL Low cost electronic humidity and temperature transmitter - Wall, duct mount relative humidity electronic transmitter - With replaceable "Humy-chip" capacitive sensor and filters |
TPRC Pressure transmitters for industrial use - Field mount pressure transmitter - Process connection: according to the selected model - Pressure range: 2... 1000 bar - Current (mA): 4...20 mA output 2 wire - Voltage (V): 0...10V output 3 wire |
||||
TP4 Pressure transmitters with display, for industrial use - Field mount pressure transmitter - Process connection: according to the selected model - Pressure range: -1...1000 bar (-100... 100.000 kPa) - Current (mA): 4...20 mA output - Integrated 4 digit LCD display |
 H5Electronic humidity, temperature and dew point transmitter - Wall, duct mount or remote sensor relative humidity electronic transmitter - With replaceable "Humy-chip" capacitive sensor and filters - Voltage, Current or PT100 output according to the selected signal and model - Alarm digital output - Reading, calculation and display of several variables: * Relative humidity (RH) * Temperature (T) * Dew Point (DP) * Temperature difference between T and DP (ΔT) - Data and event logging - RS 485 port with ModBus RTU protocol (optional) - LCD Display (optional) |
||||
TLBTA Programming external keyboard for TLB series Detached remote keyboard for big size thermostats |
TLZ35 DIN rail mount digital thermostat with defrost - DIN Rail mount controller : 70 x 84 mm, depth 60 mm (4 DIN) - 1 Configurable probe input - Up to 2 relay outputs - Internal buzzer - 1 display, 4 digits, red colour |
||||
ZH Humidity and temperature transmitter - Wall, duct mount or remote sensor - Voltage, or Current output - Capacitive - Temperature compensated - Dew resistant |
 Monitran’s MTN/5000
condition monitoring system can be used to provide a
picture of the health of plant and equipment, raise
alarms and indicate when engineering investigations may
be warranted. |
||||
 Monitran’s new
hand-held meter, the MTN/VM220, is ideal for detecting
the early signs of component wear or failure in pumps,
motors, gearboxes and other mechanical assemblies. |
 General
purpose, top-entry, velocity transducer with DC output
with integral 2-pin connector |
||||
 General
purpose, top-entry, velocity transducer with DC output
with integral 3-pin connector |
 General purpose,
top-entry accelerometer with DC output proportional to
acceleration. Made from robust stainless steel
throughout for continuous vibration monitoring |
||||
Applications • medical devices such as hospital beds • engineering equipment such as automated testers • vehicle leveling and/or alarm control sensing • solar panel positioning • safety sensing for heaters where equipment has to be kept in relative level state The picture shows one such application. Here the Smart sensor is being used in a scaffold. The scaffold is being held up by vertical cables with motors attached to adjust the length of the cables. The Smart sensors make sure the angles remain at 0˚. If any angle becomes larger than 4˚, one motor will be turned off until the angle is at 0˚ again. |
PCA-T30L-002 Categories: Capacitive Proximity Switches, Proximity Sensors. • Description Product Description Specifications § M30 Long Housing § Capacitive Sensor § Style: Cylinder Shape § Diameter: 30mm § Output Mode: AC NO § Connection mode: 2 wire § Mounting distance: 25mm,unshielded |
||||
PCA-S30-001 Categories: Capacitive Proximity Switches, Proximity Sensors. • Description Product Description Specifications § S30 Square Plastic Housing § Capacitive Sensor § Style: Squared Shape § Dim: 30x30x53mm § Output Mode: AC NO § Connection mode: 2 Wire § Mounting distance: 15mm, shielded |
 SQ24 PUSH ON
TERMINALCategories: Liquid Level / Pressure Sensors, Pressure Switches. • Description Product Description Specifications § Contact Rating: 4A 42Volts DC / 4A 230Volts AC § Maximum Voltage Peak: 1.5 KV § Hex Length: 24mm § Body Material: Zinc Plated Steel, 316SS, Brass |
||||
PD6014-25 Categories: AC Voltage Power Sensors, Smart Sensors / Custom Products. • Description Product Description Specifications § 2 Wires AC Power Switch § Voltage Range: 110 to 220 VAC § Power Capacity: 3A at 110VAC § Break Angle: 19° – 25° § Vibration Resistant |
PDS1000 Categories: Precision Shock Sensors, Smart Sensors / Custom Products. • Description Product Description Specifications § Adjustable Shock Module § Type: NPN or PNP Digital Output § Voltage Range: 6 to 30 VDC § Supply Current: 15 mA § Shock Level Resolution: ±15 mg |
||||
AU2402-7 Categories: Motion Sensors & Switches, Tilt Switches / Motion Sensors. • Description Product Description Specifications § RoHS COMPLIANT § Switching Voltage: 24V Max. § Switching Current: 0.2A Max. § Switching Capacity: 5VA Max. § Contact Resistance: 100 Ohms Max. at 5Vdc. § Operating Temperature: -37°C +100°C § Size: Over All Length: 0.354in (8.99mm) § Diameter: 0.230in (5.84mm)Max. § Movement/Vibration Sensor, Surface Mount |
 BTEL / PTUL5000The BTEL / PTUL5000 differential pressure transmitters from 1 mbar / 1 inH2O are based on piezoresistive pressure sensors and are are intended to be used with dry and non-corrosive gases. They provide two threaded pressure ports. The transmitters are calibrated and temperature compensated and offer different amplified analogue output signals. All BTEL / PTUL5000 pressure transmitters can be modified according to customer specific requirements. Typical applications include industrial measurement and control, HVAC, medical devices and instrumentation. |
||||
HMU The HMU pressure sensors provide uncalibrated and uncompensated analog mV output signals. They feature an increased media compatibility to measure gases and liquids. Very small SIL and DIP housings allow for space-saving PCB-mounting. All HMU pressure sensors can be modified according to customer specific requirements. Typical applications include industrial and pneumatic controls, instrumentation and |
|||||
